Rambler Cap And Lid Cleaning Instructions

Keeping your Rambler® Drinkware spick and span is important, and that goes for our lid and caps too. Below is an simple breakdown of how to clean ‘em all.

HOW TO CLEAN YOUR RAMBLER® DRINKWARE

FOR EASY CLEANING

  • Just pop it in the dishwasher — every inch of our drinkware is dishwasher safe. Don’t have a dishwasher? Hand washing them with mild dish soap will do just fine.

NOTICE RUST MARKS?

  • Our stainless steel rarely rusts, but if it does, polishing it up is simple. Just grab a stainless steel cleaner at your local store.
 

HOW TO CLEAN YOUR RAMBLER® LIDS AND CAPS

MAGSLIDER™ LID CLEANING INSTRUCTIONS

Our splash- and shatter-resistant MagSlider Lid is unlike any other lid. Its smooth-sliding mechanism slides shut to lock in wayward drops. For a deep cleaning, the gasket and MagSlider magnet pop right off. Even better, they’re all dishwasher safe.

  Rambler Size Chart Rambler Size Chart Rambler Size Chart
  1. 1. Pop the MagSlider off the tumbler lid and place in the dishwasher’s utensil compartment.
  2. 2. Remove gasket from the tumbler lid by using two fingers to pinch it on either side. This should make the gasket lift up from its groove. Once removed, place all parts in the dishwasher’s utensil compartment.
  3. 3. Install the gaskets placing the larger blade around gasket above the smaller blade. Ensure all parts of the cap are dry before reinstalling and storing.
  • Reminder: Larger blade around gasket should be above the smaller blade.
 

STRONGHOLD™ LID CLEANING INSTRUCTIONS

Our twist-on, twist-off StrongHold lid is backed with dual-slider magnet technology to add a strong layer between your free-flowing drink and the outside world. For a deep cleaning, the gasket and magnets pop right off. Even better, they’re all dishwasher safe.

 
To disassemble your Strong Hold Lid, Step 1 To disassemble your Strong Hold Lid, Step 2
To disassemble your Strong Hold Lid, Step 3 To disassemble your Strong Hold Lid, Step 4

To Disassemble:

  1. 1. Remove the upper magnet.
  2. 2. Half twist the lower magnet horizontally to remove.
  3. 3. Slip off the rubber sleeve covering the lower magnet.
  4. 4. Remove gasket from the lid using two fingers to pinch it on either side. Make sure slit is facing down on the lid when reinstalling.
  5. 5. Place all parts in dishwasher’s utensil compartment.

To reassemble your Strong Hold Lid

To Reassemble:

  1. Upper magnet
  2. Gasket
  3. Lower magnet
  4. Wrap rubber sleeve around lower magnet
  • Please note: This lid is not to be used with carbonated beverages. The Stronghold™ Lid ONLY fits the 20 oz. Travel Mug and is not compatible with other YETI drinkware.
 

TRIPLEHAUL™ CAP CLEANING INSTRUCTIONS

This is our classic cap, over-engineered to be leakproof, easy-to-carry, and tough as hell. It’s the foolproof way to transport your hydration from Point A to Point B without spilling a drop.

  Rambler Size Chart Rambler Size Chart
  1. Remove both gaskets below and above the threads and place in the dishwasher’s utensil compartment, then place cap on the top rack of the dishwasher.
  2. Install gaskets with flat side facing upward and the gasket grooves facing downwards toward the bottom of the cap. For a secure fit, smooth out any twists or kinks. Ensure all parts are dry before reinstalling and storing.
  • Reminder: Install gaskets with flat side facing upward and the gasket grooves facing downwards toward the bottom of the cap. For a secure fit, smooth out any twists or kinks.
 

RAMBLER BOTTLE STRAW CAP CLEANING INSTRUCTIONS

The best way to drink on the move? The Straw Cap — a one-handed flipping operation. It also includes the sturdy TripleHaul Handle for easy hauling.

  Rambler Size Chart Rambler Size Chart Rambler Size Chart
  1. Flip open top.
  2. Remove the straw and place in the dishwasher’s utensil compartment. For more thorough cleaning, use a small cleaning brush.
  3. Remove the circular cap gasket and place in the dishwasher’s utensil compartment, then place cap on the top rack of the dishwasher (with mouthpiece flipped open).
  4. Re-Install: ensure all parts are dry before reinstalling and storing. Look closely at the gasket, you’ll notice there are two “blades,” one stands out farther than the other. The flat side of the gasket goes against the cap, blades out, larger blade on top.

Looking to Hand-Wash Instead?

  1. Disassemble straw and gasket(s) as mentioned above.
  2. Submerge all parts (cap, straw, gasket) in warm, soapy water for up to 2 hours.
  3. Cap cleaning: under running water, use a finger to gently lift the gaskets around the pressure valve, rinsing away any built up grime. DO NOT try to remove this gasket.
  4. Rinse and dry all pieces thoroughly before reinstalling.
 

RAMBLER CHUG CAP CLEANING INSTRUCTIONS

This two-piece cap includes the narrow-spout base and a cap with the TripleHaul Handle. The top cap opens with a quick half-twist to reveal the clear-top narrow “chug” spout, which is great for keeping the ice cubes back while downing some water.

  Rambler Size Chart Rambler Size Chart
  1. Disassemble Chug Cap from its handle.
  2. Remove both gaskets below and above the threads and place in the dishwasher’s utensil compartment. Place cap and handle on the top rack of the dishwasher.
  3. Install the gaskets placing the larger blade around gasket above the smaller blade. Ensure all parts are dry before reinstalling and storing.
 

HOTSHOT™ CAP CLEANING INSTRUCTIONS

This innovative and insulated 100% leakproof cap lives up to its name by locking in piping-hot temperatures. For added convenience, we built in a 360-degree drinking experience. Which means with just a half twist and a click, you can sip from any side.

  Rambler Size Chart Rambler Size Chart Rambler Size Chart
  1. From the closed position, twist the inner cap counterclockwise. After hearing two clicks, the inner cap can be removed for a deep cleaning in the dishwasher.
  2. Remove both gaskets below and above the threads and place in the dishwasher’s utensil compartment. Place inner and outer cap on the top rack of the dishwasher.
  3. Install the gaskets placing the larger blade around gasket above the smaller blade. Ensure all parts are dry before reinstalling and storing.
 

CUP CAP CLEANING INSTRUCTIONS

Transform your Rambler Bottles with our heat-locking, two-in-one companion — the Cup Cap. Not only is it compatible with every Rambler Bottle, but it also offers twice the functionality. As an insulated cap, it helps keep your coffee, tea, or even whiskey at the perfect temperature. And when you twist it off, you’ve got a double-wall vacuum insulated cup.

  Rambler Size Chart Rambler Size Chart Rambler Size Chart Rambler Size Chart
  1. Disassemble the adapter, inner cap, and 5 oz. Cup from the Rambler Bottle.
  2. To remove the inner cap, forcefully twist counterclockwise until it fully pops out.
  3. Remove both gaskets below and above the threads on the adapter and inner cap and place in the dishwasher’s utensil compartment. Place adapter, inner cap, and 5 oz. Cup on the top rack of the dishwasher.
  4. Install the gaskets placing the larger blade around gasket above the smaller blade. Ensure all parts are dry before reinstalling and storing.